Hi,
After an upgrade of my Compaq Presario to windows XP I have a problem to upgrade the graphic driver for my RAGE LT PRO AGP 2X. According to Microsoft release notes
there can be a problem with Rage3-based display cards and you should contact the vendor.
After the upgrade the resolution was set to lowest level and could not be changed,
and the problem is that I can't change my adapter driver, the computer shuts down just after the installation restart.
I have found some information that ATI Rage Pro chipset will not allow reference or updated
drivers to be installed due to the hardware identification string is not being present in the
driver setup information (INF) file, see http://www.geocities.com/ziyadhosein/inf.htm
My adapter information details are:
Chip Type: ATI 3D RAGE LT PRO AGP 2X (A2U2)
DAC Type: ATI Internal DAC
Adapter String: 1002-4C42-DC-1002-4C42
The upgrade display driver for windows XP and ATI RAGE PRO have the details:
file: wxp-j5-30-1-B02.exe
Verison: 5.10.2600.6010 (02/28/2002)
I have tried to modify the INF file (ATIIXPAD.INF) suggested by the above web page.
But I'm not really sure if I have done the right modification.
Below are the two strings I have added and played with and I have tried several
combinations of the strings but with no success.
Now I'm stuck and I need help how this should be set.
[ATI.Mfg]
RAGE LT PRO AGP 2X = ati2mpad, PCI\VEN_1002&DEV_4C42&SUBSYS_4C421002, PCI\VEN_1002&DEV_4C42
[ati2mpad]
PCI\VEN_1002&DEV_4C42&SUBSYS_4C421002, PCI\VEN_1002&DEV_4C42
Any support and suggestions are very much appreciated.
/AB
After an upgrade of my Compaq Presario to windows XP I have a problem to upgrade the graphic driver for my RAGE LT PRO AGP 2X. According to Microsoft release notes
there can be a problem with Rage3-based display cards and you should contact the vendor.
After the upgrade the resolution was set to lowest level and could not be changed,
and the problem is that I can't change my adapter driver, the computer shuts down just after the installation restart.
I have found some information that ATI Rage Pro chipset will not allow reference or updated
drivers to be installed due to the hardware identification string is not being present in the
driver setup information (INF) file, see http://www.geocities.com/ziyadhosein/inf.htm
My adapter information details are:
Chip Type: ATI 3D RAGE LT PRO AGP 2X (A2U2)
DAC Type: ATI Internal DAC
Adapter String: 1002-4C42-DC-1002-4C42
The upgrade display driver for windows XP and ATI RAGE PRO have the details:
file: wxp-j5-30-1-B02.exe
Verison: 5.10.2600.6010 (02/28/2002)
I have tried to modify the INF file (ATIIXPAD.INF) suggested by the above web page.
But I'm not really sure if I have done the right modification.
Below are the two strings I have added and played with and I have tried several
combinations of the strings but with no success.
Now I'm stuck and I need help how this should be set.
[ATI.Mfg]
RAGE LT PRO AGP 2X = ati2mpad, PCI\VEN_1002&DEV_4C42&SUBSYS_4C421002, PCI\VEN_1002&DEV_4C42
[ati2mpad]
PCI\VEN_1002&DEV_4C42&SUBSYS_4C421002, PCI\VEN_1002&DEV_4C42
Any support and suggestions are very much appreciated.
/AB